Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
We've noticed the article involving Tools You Need to Install a New Bathtub down the page on the net and concluded it made sense to talk about it with you on my blog.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is easily easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the work as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to take into consideration using one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This article will certainly help you mount a brand-new bathtub in your bathroom if you have actually already bought a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipes have actually been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are handy in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub ought to wait until the bath tub has been used at the very least once as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to pass through the wall surface between the bath as well as the tiling, bring about complications with moisture as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that write-up about How to Install a Bathtub Yourself through an associate on another domain. Are you aware of another individual who is very much interested in the topic? Do not hesitate to promote it. We value reading our article about How to Install a Bathtub Yourself.
At This Website
Report this page